EKF - Short Profile
EKF - Short Profile
SF2-CANDY

CAN Module Carrier • Up to 16 x CAN-FD • CompactPCI® Serial



SF2-CANDY

Description

Ordering Information

Product Information

Block Diagram

General Information
Products One Click

All You Need to Know


SF2-CANDY • 16 x CAN-FD

Photo Gallery

1 | 2 | 3 | 4
© EKF • Images show up in a secondary browser tab or window


SF2-CANDY

CompactPCI® Serial • CAN Controller

8 Port CAN 2.0B • 16 Port CAN-FD


The SF2-CANDY is a quad PCI Express® Mini Card carrier, suitable for CompactPCI® Serial systems. The board can be used together with PCIe® based CAN fieldbus modules, available as single-port, dual-port or even quad-port CAN controllers. This results in a scalable solution from 1 up to 16 CAN I/O ports, wired to a common D-SUB front panel connector. Validated CAN modules are available for classic CAN 2.0A/B, and also CAN FD (Flexible Data Rate).

Two front panel connector solutions are available from stock, either D-SUB 25-position for up to 8 CAN 2.0B ports, or D-SUB 50-position for up to 16 CAN-FD ports. Each CAN port is individually isolated for optimum fieldbus reliability.
The SF2-CANDY is equipped with an on-board PCI Express® packet switch, and can be installed into any peripheral slot of a CompactPCI® Serial backplane.

SF2-CANDY • 16 x CAN-FD

SF2-CANDY • 16 x CAN-FD

Feature Summary

General
  • PICMG® CompactPCI® Serial standard (CPCI-S.0) peripheral slot card
  • Single size Eurocard 3U 4HP 100x160mm2
  • Backplane connector P1 (peripheral slot PCIe® x1)

PCI Express® Interface
  • Gen2 PCI Express® 6-port packet switch
  • Upstream port: PCI Express® x1 Gen2 (5.0Gbps) or Gen1 (2.5Gbps) supported
  • Downstream ports: 4 x PCIe® Mini Card, Gen1 and Gen2 support

PCI Express® Mini Card
  • 4 x PCI Express® Mini Card sockets, full-size or half-size modules, PCIe® based
  • Validated with PEAK System PCAN-miniPCIe Dual Channel for CAN 2.0A and 2.0B
  • Validated with PEAK System PCAN-miniPCIe FD Four Channel for CAN FD

Front Panel Connector
  • 4 HP front panel design
  • D-SUB 37-pin connector and cable harness for up to 4 x PCAN-miniPCIe (8 ports)
  • D-SUB 50-pin connector and cable harness for up to 4 x PCAN-miniPCIe FD (16 ports)
  • Custom specific front panel design, e.g. 8 x D-SUB 9-pin connectors with 12HP front panel width

Applications
  • Test equipment for automotive networks
  • Industrial automation
  • Autonomous devices - IoT
  • Medical equipment

Special Features SF2-1080-CANDY • CAN 2.0A/B
  • Up to 4 x Peak System PCAN-miniPCIe dual channel CAN I/O module, PCIe® based
  • 4 x 2 High-speed CAN channels (ISO 11989-2)
  • Bit rates from 5 kbit/s up to 1 Mbit/s
  • Bus length up to 13km
  • Compliant with CAN specifications 2.0A (11-bit ID) and 2.0B (29-bit ID)
  • FPGA implementation of the CAN controller (SJA1000 compatible)
  • NXP PCA82C251 CAN transceiver
  • Galvanic isolation on the CAN connection up to 300 V, separate for each CAN channel
  • Extended operating temperature range from -40°C to +85°C
  • Full device driver support Windows 10, 8.1, 7 and Linux 32/64-bit
  • Programming interface PCAN-Basic for developing applications with CAN connection
  • Programming interfaces for standardized protocols from the automotive sector
  • 4HP front panel width - up to 8 CAN ports wired to a common front panel connector D-SUB 25-pin
  • 4HP, 8HP and beyond custom specific front panel design with other connector(s) on request

Special Features SF2-2160-CANDY • CAN FD
  • Up to 4 x Peak System PCAN-miniPCIe FD quad channel CAN I/O module, PCIe® based
  • 4 x 4 High-speed CAN channels (ISO 11989-2)
  • Complies with CAN specifications 2.0A/B and FD
  • CAN FD support for ISO and Non-ISO standards switchable
  • CAN FD bit rates for the data field (64 bytes max.) from 25 kbit/s up to 12 Mbit/s
  • CAN bit rates from 25 kbit/s up to 1 Mbit/s
  • FPGA implementation of the CAN controller (SJA1000 compatible)
  • NXP TJA1044GT CAN transceiver
  • Galvanic isolation on the CAN connection up to 300 V, separate for each CAN channel
  • PCIe data transfer via bus master DMA
  • DMA memory access operations with 32- and 64-bit addresses
  • Measurement of bus load including error/overload frames on the physical bus
  • Induced error generation for incoming and outgoing CAN messages
  • Extended operating temperature range from -40°C to +85°C
  • Full device driver support Windows 10, 8.1, 7 and Linux 32/64-bit
  • Programming interface PCAN-Basic for developing applications with CAN connection
  • Programming interfaces for standardized protocols from the automotive sector
  • 4HP front panel width - up to 16 CAN ports wired to a common front panel connector D-SUB 50-pin
  • 4HP, 8HP and beyond custom specific front panel design with other connector(s) on request

CANopen®
  • Fully CIA CANopen® compliant protocol set
  • SDO - PDO - NMT - Special Functions - Error Control
  • Software tools available on request:
  • CANopen® Magic - Analysis-, Development, and Simulation Software
  • CANopen® PC Developer Kit - Development Package for CANopen® Applications
  • Embedded CANopen® Library
  • CANopen® Controller Library


Regulatory, Environment
  • Designed & manufactured in Germany
  • ISO 9001 certified quality management system
  • Long term availability
  • Rugged solution - coating, sealing, underfilling on request
  • RoHS compliant
  • Operating temperature -40°C to +85°C (industrial temperature range)
  • Storage temperature -40°C to +85°C, max. gradient 5°C/min
  • Humidity 5% ... 95% RH non condensing
  • Altitude -300m ... +3000m
  • Shock 15g 0.33ms, 6g 6ms
  • Vibration 1g 5-2000Hz
  • MTBF 39.6 years (carrier card)
  • EC Regulatory EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)


SF2-CANDY • Simplified Block Diagram

SF2-CANDY • Simplified Block Diagram
Ordering Information
Please refer to List 21 for popular SKUs